Guide · Homeowners · 3 min read · Updated 16 November 2026
Built-In Oven and Hob Removal: A Practical Guide
Short answer
A built-in oven is removed by isolating its power, unscrewing it from the housing through the side trim, sliding it forward and disconnecting the plug or cable. A hob is removed by isolating the supply, releasing the clamps underneath and cutting the perimeter sealant. Gas hobs need a Gas Safe registered engineer. Built-in oven removal costs £55–£85 and hob removal starts from £45.
How built-in ovens are fitted
A built-in oven sits on a shelf inside a tall housing or under the worktop, with a gap behind it for ventilation and the cable. It is held in place by two or four screws driven through the side trim or front frame into the cabinet sides. Those screws are often only visible with the door fully open. Single ovens are typically around 30 to 40 kg, and double ovens are heavier because of the second cavity and extra glass.
The power connection is either a plug into a socket or fused spur in the next cupboard, or a hardwired cable to a cooker connection outlet. The second needs a competent electrician to isolate it.
Removing a built-in oven step by step
Once the power is isolated, the oven door is opened and the fixing screws removed. The oven is eased forward a few centimetres at a time, with a second person supporting the front, because it tips forward as the back leaves the shelf. The cable is followed back and unplugged or disconnected at the outlet. Shelves and trays come out first to lighten the load and stop glass rattling.
In tall housings, the oven may be at chest height. That is a two-person lift with a clear landing spot below. We protect the floor and the cabinet edges with blankets so nothing is scuffed.
- Isolate the power at the switch, spur or consumer unit
- Remove all shelves, trays and loose racks
- Open the door and find the side-trim fixing screws
- Slide forward slowly with someone supporting the front
- Disconnect the plug or cable and keep the housing clear for the new oven
How hobs are held in place
Hobs drop into a cut-out in the worktop and sit on a foam or rubber seal. Underneath, small metal clamps screw into the worktop edge to hold them down. Many installers also run a bead of silicone around the edge. On laminate worktops this is easy to cut, but on granite, quartz and solid wood it needs a careful hand to avoid lifting chips from the edge of the cut-out.
Gas hobs are connected by a fixed pipe or an approved flexible connector, so a Gas Safe registered engineer must disconnect and cap them first. Induction and ceramic hobs are usually on a dedicated electrical circuit and need isolation by an electrician.
| Hob type | Typical connection | Before removal |
|---|---|---|
| Gas hob | Fixed pipe or approved flexible connector | Gas Safe engineer disconnects and caps |
| Induction hob | Dedicated circuit, cooker outlet | Electrician isolates the circuit |
| Ceramic hob | Dedicated circuit or shared with oven | Electrician isolates the circuit |
| Solid plate hob | Dedicated circuit | Electrician isolates the circuit |
| Domino or two-zone hob | Plug, spur or dedicated circuit | Check the connection before booking |
Taking out a hob without damaging the worktop
With the supply safe, the clamps are released from inside the base unit. A sharp blade is then run around the sealant line, holding the blade flat against the hob frame rather than the worktop. The hob is lifted gently from the front so the seal peels away rather than tearing the worktop surface. On stone worktops, plastic wedges are used to break the seal gradually.
Glass hobs crack if they are flexed, so they are lifted evenly from both sides. Once out, the cut-out is cleaned of old sealant and foam so the new hob can sit flat.
Solid wood worktops need one extra check. The exposed edges of the cut-out are often unsealed, and once the hob is out they are open to moisture from cleaning and spills. If the replacement will not go in the same day, cover the opening and wipe the raw timber edges dry. Oiling them before the new hob is fitted helps stop swelling and blackening around the opening over time.
Matching the new appliance to the old opening
Before the old appliance goes, check that the new one fits the same opening. Built-in oven cut-outs are fairly standard, but hob cut-outs vary between brands and between gas and induction models. A slightly larger cut-out can be covered by a wider hob frame, but a smaller one means the worktop must be cut, which is work for a kitchen fitter or stone specialist.
Measure the existing cut-out width and depth, and compare it with the installation drawing for the new hob. Switching from gas to induction may also need a new dedicated circuit, so ask an electrician to check the supply before ordering. Induction hobs often draw more power than the gas hob or ceramic hob they replace.
Costs and what to tell us
Built-in single or double oven removal costs £55–£85, including unscrewing the fixings, protecting the cabinets and recycling the oven. Hob removal starts from £45. Removing an oven and hob together, or adding them to a full kitchen strip-out with the extractor, dishwasher and fridge, is cheaper per item than booking them separately.
When you request a quote, tell us the appliance types, the worktop material, how each one is connected and where the kitchen is in the property. Photos of the oven housing and the connection points help us confirm a fixed price first time.
Questions people also ask
Can I remove a built-in oven myself?
If it runs from a plug, many people can, with a second person to take the weight. Isolate the power, remove the shelves, take out the side-trim screws and slide it forward slowly. If it is hardwired to a cooker outlet, an electrician should isolate and disconnect it before it is moved.
Will removing my hob damage the worktop?
Not if the clamps are released first and the sealant is cut carefully. The risk is highest on stone and quartz, where forcing the hob can chip the edge of the cut-out. A careful removal with a sharp blade and plastic wedges leaves the opening clean for a replacement.
Do you remove extractor hoods as well?
Yes. Extractor hoods are commonly removed with the oven and hob during a kitchen strip-out. Chimney hoods are unhooked from their wall brackets and the ducting is released, while integrated hoods are unscrewed from the wall unit. The electrical connection needs isolating first if the hood is hardwired.
Written and checked by the Cooker Disposal team. Read our editorial policy.
More guides
How Much Does Cooker Disposal Cost in the UK?
Cooker disposal in the UK costs from £45 for a freestanding cooker that is already disconnected and easy to reach. Built-in single or double ovens…
How to Disconnect a Cooker: Gas, Electric and Who Can Do It
A gas cooker must be disconnected and capped by a Gas Safe registered engineer under the Gas Safety (Installation and Use) Regulations 1998. A…
How to Get Rid of an Old Cooker: UK Options Compared
To get rid of an old cooker in the UK, use the retailer's take-back service when you buy a new one, book a council bulky waste collection, take it to…
Kitchen Refit Appliance Removal: A Preparation Checklist
Before a kitchen refit, book Gas Safe and electrical disconnections first, then schedule removal of the cooker, hob, oven, extractor, dishwasher,…
Get a free cooker disposal quote
Tell us what you need and we'll come back with a clear price.
Request a quote